... Just did a continuity measurement between each of the tilt switches and the tilt relay and the mech panel slam switch seems to have a short since it has...
Thanks for the info. I thought I was reading the schematics right, but someone else email me and said there bonus unit was the same way (not wired together)...
... If you remove the disc you will see that the two pin holders have a wire connecting them together. This is the redundant extra connection in case the...
Thanks John. Yes, both wires were missing (which seemed odd). The backup line and the actual jumper line were both gone. I think there were signs of both...
Thanks RB for the tip. Thaks TXSteven, too. There are two lamp sockets under the hood. I thought they were just to provide a light in the cabinet. Now I...
I was wondering if any of you have ever applied triple thick over a large open (clear) area on a backglass, such as the center section of a Gottlieb Black...
I never use TT over any clear area, no matter how large or how small. In my experience the TT distorts the clear areas, especially in cases where the clear...
IMHO if it is a large area of clear, it would be best to mask off the area and NOT spray the TT. No matter how good a spray job you do on the clear area it...
Then, once you get a #455 bulb in there, it will complete the "hold" circuit until it heats up and the thermal switch inside it opens up to turn the bulb off....
In This Update: 1. What's New In-Store 2. Did You Know? 3. FREE T-Shirts! 4. Satisfaction Guaranteed 5. Shop & Save ... 1. What's New In-Store To see what was...
I recently acquired a 1975 Bally Knockout, but am having an issue which keeps the score motor running continuously. Interestingly enough it starts to run as...
Thanks Bob, the coins switches themselves appear ok, however I noticed that the lockout strip was not connected to the latch assembly, when I connected the...
Here is a list of the EM games in the free play area at one time or another on Fri and Sat at Allentown. Was only there for a short time on Sun morning to say...
... Hey, fredo, That's normal for when the score motor goes; the lockout (really a lock-IN) engages when the score motor is at zero position, and locks out...
I was moving around my Bally Fireball to allow room for a new pin. I have felt coasters under it, so I just glided it across the room to its new position. ...
Check your EOS (end of stroke switch) to make sure the gap is correct. If the right flipper is OK, and is strong the way you like, adjust the EOS on the left...
I finally got a match unit for my Wms Triple Strike, and not wanting to mess with wires, I decided I would remove the piece with the spring and put it on the...
I am in Toms River New Jersey and have 2 project pins for sale. 1 is a Williams' Space Odyssey, average glass & playfield, cabinet painted white, the other is...
Just made a photo album of this name. I put 4 pictures of items, looking to get a name of each so I can research them. Looking at $50 for each. Also picking...
... Hi Marty, The gambling games are Keeney Flasher machines. Comparable to today's bar machine where you earn credits and claim your winnings with the...
... http://www.pinrepair.com/bally/index.htm Recommendation: Read parts 1,2, and 3. If you want to get really fancy, save the pages to a flash drive or cdrom...
I'm going through a '71 Bally Vampire, and both the legs and coin door are in serious need of a repaint. I normally use Dupli-color Storm Gray for legs on...
Q: Are all of the tilt switches in the open position normally? The kids were messing around and I dont have a schematic. Ive cleaned and checked everything....
Hope everyone that went to Allentown had a great time. I finally did tried out the SprayMax 2k Automotive Clear Coat that comes in a can. I summarized and took...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
